A larger percentage of us use shoes among the basic needs of a human being. In as much as human needs are insatiable, they also get worn out. It puts one of that sometimes something like a shoe could have a sole separation at the moment you may not afford to get yourself another pair. This happens to us because not all the money can be channeled towards clothing therefore when a shoe and sole separation occurs, you can go through the following steps to know how to fix a shoe sole separation.
The following is the steps for the shoe sole fixing:
You don’t have to incur shoe repair costs while you can do some minor repairs. If you have a shoe sole separation, the following steps will help you repair the shoe and give it a nice look again.
Clean the area of repair
It is essential to ensure that the part of the shoe sole to be repaired is clean before the fixing process is underway. You need not only to clean the area like ordinary cleaning, but you need some special chemicals such as acetone and isopropyl solvents. You rub the chemicals in a piece of clothing. Give the cleaned region approximately five minutes.
Before the work is done, you should be prepared in all the aspects to perform a specific task efficiently. During preparations, take away the insoles for boots that are too big of the shoe and stuff the shoe using some newspapers. This stuffing ensures that your shoe becomes firm while you are fixing it, thus enabling maximum absorbance of the glue that can accidentally ooze into your shoe.
b) The Glue
The glue is the most critical requirement when you are fixing your shoe. The glue is some sticky liquid of high viscosity. The shoe goo glue is among the best type of glue you can trust for fixing your shoe. While you now are ready to glue your shoe ensure you put on disposable hand gear to avoid contact of your skin and the glue. Also, ensure your working table there is some sheet in case of any glue drip it does not fall on the table.
Follow the instruction strictly on your glue tube before opening. Prick the glue tube using some needle to open it up, and you can apply some jelly on the opening. This is important as it can prevent the closure of the glue tube later on.
c) Apply The Glue To The Sole
Squeeze the glue from the tube directly onto your sole, although this only applies to the large areas yet to ensure proper fixing you need to glue every other part so to reach the small areas you need materials such as the toothpick. Using a cotton swab, you can now ensure that the glue is evenly spread around the area of repair. It is not yet time that you glue the toe cap. According to the instructions from the manufacturer, acetone is the cleaning solvent that is greatly preferred over others.
d) Clamping The Shoe
After applying the glue, allow it to stand for about two minutes before you can bring the surfaces into contact. When the two minutes elapses, you can use some weight to keep the sole and the upper shoe together.
You can do this in two steps. You can glue the pole part then the toe cap later or the later one to be glued.
You should allow the glue to stand for 24 hours to ensure maximum attachment of the sole to the upper part.
e) Glue The Toe Cap
After gluing the sole and left to stand for 24 hours, it is now time that you should glue the toe cap.
You will need to put some wax paper in between the block of wood and the toe cap to avoid attachment of glue to the block of wood. Also, the wax paper between the shoe and the block is important to avoid the shoe from being attached to the wood after 24 hours.
f) Trimming The Squeeze-Out
Some glue squeezes out from the shoe. You can remove your shoe from contraption after 24 hours. The glue that squeezes out needs to be trimmed out, and this can be achieved by the use of equipment that every workshop should have, it is called the xuron micro shears. This equipment will help you around while working with your shoe. It is accurate and precise. The use of this equipment has no damage to your shoe; therefore, it can be significantly trusted.
g) Shoe Repair Is Now Complete
After following all the steps highlighted above to the later, the shoe is now repaired successfully, and the results will be great. You now are free to take off the paper used for stuffing from the shoe, if they had a removable insole, you can return them back. However, if the insole is not removable, it can lose its shape due to the paper used for stuffing. This should not worry you because the effect can be reversed back to normal.
I hope the article has served you the purpose. Your shoe can now serve you a little more extra before you can purchase another or you can return back your favorite shoe into a useful form, and you do not have to lose it anymore. Say no more to shoe separation. With these tips, I hope it is going to be helpful to you any time your shoe, and the sole are separated from each other. You can fix it back together and enjoy wearing your shoes again.